描述
BENTLY 3500/22M-01-01-01是一款高性能瞬态数据接口模块，专为工业自动化和机械保护系统设计，是BENTLY 3500监测系统的核心组件之一。以下是其详细产品简介：
一、功能概述
数据接口与通信
-作为3500监测系统与System 1状态监控、诊断软件及3500系统配置软件的接口，实现数据无缝传输。
-结合3500/20机架接口模块（RIM）功能与TDXnet等通信处理器，支持稳态和瞬态动态（波形）数据的连续采集与传输。
数据采集能力
-静态数据：标准配置支持静态数据采集，包括传感器测量值、幅值及相位等。
-瞬态数据：通过可选通道启用磁盘，可记录高分辨率瞬态事件（如振动冲击、机械故障），采集速度与时间增量可独立编程。
系统集成
-安装于3500机架电源旁边的插槽1，与M系列监视器（如3500/40M、3500/42M）协同工作，支持48通道波形同步采样。
二、技术参数
硬件特性
-功耗：10.5瓦
-接口：USB-B前面板、100Base-FX光纤以太网、10/100Base-TX自适应以太网
-指示灯：OK LED（运行状态）、TX/RX LED（通信活动）、TM LED（跳闸模式）、CONFIG OK LED（配置有效性）
数据处理
-波形采样：直流耦合，支持同步与异步数据采集
-存储限制：瞬态事件数量受限于模块内存容量
-报警数据：触发后自动记录前后10分钟静态值（1秒间隔）、前后20秒/10秒静态值（100毫秒间隔），及波形数据（警报前2.5分钟/后1分钟，10秒间隔）。
三、应用场景
工业监测：电力、石油、化工、冶金等行业中旋转设备（如汽轮机、压缩机）的振动、位移、温度监测。
机械保护：超速保护、轴承故障预警、齿轮异常检测等。
智能工厂：与智能制造系统集成，支持预测性维护与资产健康管理。
四、系统兼容性
机架要求：每个3500机架需配置1个TDI或RIM，且必须安装在插槽1。
传感器支持：兼容电涡流、速度、加速度等传感器，需通过外部电源模块供电。
冗余设计：支持三重模块冗余（TMR）组态，增强系统可靠性。
BENTLY 3500/22M-01-01-01 is a high-performance transient data interface module designed for industrial automation and machinery protection systems.It is one of the core components of the BENTLY 3500 monitoring system.The following is a detailed product introduction:
I.Functional Overview
Data Interface and Communication
-Serves as an interface between the 3500 monitoring system and System 1 status monitoring,diagnostic software and 3500 system configuration software to achieve seamless data transmission.
-Combines the 3500/20 rack interface module(RIM)function with communication processors such as TDXnet to support continuous acquisition and transmission of steady-state and transient dynamic(waveform)data.
Data acquisition capabilities
-Static data:The standard configuration supports static data acquisition,including sensor measurements,amplitude and phase.
-Transient data:Enable disk through optional channels to record high-resolution transient events(such as vibration shock,mechanical failure),and the acquisition speed and time increment can be independently programmed.
System Integration
-Installs in slot 1 next to the 3500 rack power supply and works with M-Series monitors(such as 3500/40M,3500/42M)to support 48 channels of simultaneous waveform sampling.
2.Technical Parameters
Hardware Features
-Power consumption:10.5 watts
-Interfaces:USB-B front panel,100Base-FX fiber optic Ethernet,10/100Base-TX adaptive Ethernet
-Indicator lights:OK LED(operating status),TX/RX LED(communication activity),TM LED(trip mode),CONFIG OK LED(configuration validity)
Data processing
-Waveform sampling:DC coupling,supports synchronous and asynchronous data acquisition
-Storage limit:The number of transient events is limited by the module memory capacity
-Alarm data:After triggering,the static valuesof 10 minutes before and after(1 second interval),20 seconds/10 seconds before and after(100 millisecond interval),and waveform data(2.5 minutes before the alarm/1 minute after the alarm,10 seconds interval)are automatically recorded.
3.Application scenarios
Industrial monitoring:Vibration,displacement,and temperature monitoring of rotating equipment(such as turbines and compressors)in industries such as power,petroleum,chemical,and metallurgy.
Mechanical protection:overspeed protection,bearing fault warning,gear abnormality detection,etc.
Smart Factory:Integrate with smart manufacturing systems to support predictive maintenance and asset health management.
IV.System Compatibility
Rack Requirements:Each 3500 rack must be configured with 1 TDI or RIM,and must be installed in slot 1.
Sensor Support:Compatible with eddy current,velocity,acceleration and other sensors,and must be powered by an external power module.
Redundant Design:Supports triple module redundancy(TMR)configuration to enhance system reliability.
