描述
一、核心功能与定位
产品类型
功能：16点离散输出模块，属于GE Fanuc现场控制系列，支持正逻辑源型输出，适用于工业自动化系统中的设备控制（如指示灯、继电器、电磁阀等）。
兼容性：与总线接口单元（BIU）配合使用，支持扩展I/O解决方案，兼容GE Fanuc的PAC（可编程自动化控制器）系统。
核心特性
高可靠性：内置5A保险丝保护，支持电源极性错误检测与故障诊断。
灵活扩展：支持现场安装或控制室安装，兼容多种工业网络协议（如Modbus、DeviceNet）。
环境适应性：工作温度范围广（-25°C至+70°C），适应复杂工业环境。
二、技术参数
硬件配置
输出通道：16点独立离散输出，支持正逻辑（源型）控制，每点最大电流0.5A，总模块电流4A。
电源要求：外部DC电源输入范围10-30VDC（标称24VDC），模块自身从BIU电源汲取111mA电流。
接线端子：集成25个端子，支持AWG#14-22电线，可扩展至AWG#14-16（需跳线）。
电气特性
响应时间：典型响应时间为200ms（0.5A阻性负载）。
输出压降：最大0.5V，漏电流≤0.5mA（30VDC时）。
浪涌电流：最大2A（持续100ms）。
环境与认证
工作温度：-25°C至+70°C（部分版本支持-10°C至+50°C）。
湿度范围：5%-95%（非冷凝）。
认证标准：UL认证，符合工业级抗干扰与防护要求。
三、功能特性
诊断与保护
保险丝监测：通过LED指示灯实时显示保险丝状态及电源电压异常（低于9.8VDC时触发报警）。
故障上报：向BIU发送保险丝熔断或电源故障信息，支持远程诊断。
通信与集成
协议支持：兼容Modbus、DeviceNet等工业协议，支持以太网通信（部分版本）。
模块化设计：支持热插拔安装，便于维护与扩展。
信号隔离
光隔离技术：逻辑元件与现场输出隔离，防止信号干扰与噪声影响。
IC698CPE040
IC698CPE040
1.Core functions and positioning
Product Type
Function:16-point discrete output module,belongs to the GE Fanuc field control series,supports positive logic source output,and is suitable for equipment control in industrial automation systems(such as indicator lights,relays,solenoid valves,etc.).
Compatibility:Used with the Bus Interface Unit(BIU),supports extended I/O solutions,and is compatible with GE Fanuc’s PAC(Programmable Automation Controller)system.
Core features
High reliability:Built-in 5A fuse protection,supports power polarity error detection and fault diagnosis.
Flexible extension:Supports on-site installation or control room installation,compatible with a variety of industrial network protocols(such as Modbus,DeviceNet).
Environmental adaptability:Wide operating temperature range(-25°C to+70°C),adapting to complex industrial environments.
2.Technical parameters
Hardware configuration
Output channel:16-point independent discrete output,supports positive logic(source type)control,the maximum current per point is 0.5A,and the total module current is 4A.
Power requirements:The input range of external DC power supply is 10-30VDC(nominal 24VDC),and the module itself draws 111mA current from the BIU power supply.
Terminals:Integrated 25 terminals,supports AWG#14-22 wires,and can be expanded to AWG#14-16(requires jumper).
Electrical characteristics
Response time:Typical response time is 200ms(0.5A resistive load).
Output voltage drop:maximum 0.5V,leakage current≤0.5mA(at 30VDC).
Inrush current:maximum 2A(lasting 100ms).
Environment and certification
Operating temperature:-25°C to+70°C(some versions support-10°C to+50°C).
Humidity range:5%-95%(non-condensing).
Certification standard:UL certified,complies with industrial-grade anti-interference and protection requirements.
3.Functional characteristics
Diagnosis and protection
Fuse monitoring:The fuse status and power supply voltage are displayed in real time through the LED indicator(an alarm is triggered when it is lower than 9.8VDC).
Fault reporting:Send fuse blown or power failure information to BIU,supporting remote diagnosis.
Communication and integration
Protocol support:compatible with industrial protocols such as Modbus,DeviceNet,etc.,and supports Ethernet communication(some versions).
Modular design:supports hot-swap installation,easy maintenance and expansion.
Signal isolation
Optical isolation technology:Logic components are isolated from the field output to prevent signal interference and noise influence.
