描述
一、产品概述
GE IC693MDL340是通用电气（GE Fanuc）推出的交流输出模块，属于90-30系列可编程逻辑控制器（PLC）系统的核心组件。该模块专为工业自动化控制场景设计，提供16个独立交流输出点，支持高可靠性负载控制，适用于电感负载、白炽灯等设备。其核心功能包括信号隔离、浪涌电流保护、状态指示等，广泛应用于制造业、能源、化工、电力等领域。
二、核心功能与技术参数
1.输出配置
输出点数：16点，分为两组（每组8点），每组配备独立公共端，支持独立或统一电源供电。
输出电压范围：85-132 V AC，50/60 Hz。
电流能力：
每点最大输出电流：0.5 A。
每组最大电流：3 A。
浪涌电流处理：支持高浪涌电流，适用于电感负载和白炽灯负载。
2.保护与隔离
保险丝保护：每组配备3 A保险丝，防止过载或短路。
RC缓冲器：每个输出点内置RC缓冲器，抑制电力线瞬态噪声干扰。
光电隔离：输入/输出信号隔离设计，提升抗干扰能力。
3.状态指示
LED指示灯：顶部配备16个绿色LED指示灯（A1至A8），显示各输出点开/关状态。
故障报警：红色“F”LED指示灯亮起表示保险丝熔断。
4.电源与功耗
工作电源：仅支持交流电源（120 V AC）。
功耗：所有输出开启时功耗为315 mA（来自背板5 V总线）。
5.环境适应性
安装方式：支持DIN导轨安装，兼容90-30系列PLC底板（5或10插槽）。
响应时间：开启响应时间≤1 ms，关闭响应时间≤1 ms。
工作温度：-20°C至60°C（部分型号扩展至-25°C至70°C）。
三、典型应用场景
工业控制
电机启停、电磁阀控制、照明系统管理。
能源与电力
变电站设备控制、发电机组保护。
化工与制造
流程控制、生产线设备联动。
基础设施
水处理系统、楼宇自动化设备。
IC698CPE040
IC698CPE040
1.Product Overview
GE IC693MDL340 is an AC output module launched by GE Fanuc and is a core component of the 90-30 series programmable logic controller(PLC)system.This module is specially designed for industrial automation control scenarios,providing 16 independent AC output points,supporting high-reliability load control,and is suitable for inductive loads,incandescent lamps and other equipment.Its core functions include signal isolation,surge current protection,status indication,etc.,and are widely used in manufacturing,energy,chemical industry,electricity and other fields.
2.Core functions and technical parameters
1.Output configuration
Output points:16 points,divided into two groups(each group of 8 points),each group is equipped with an independent public end,supporting independent or unified power supply.
Output voltage range:85-132 V AC,50/60 Hz.
Current capability:
Maximum output current per point:0.5 A.
Maximum current per group:3 A.
Inrush current processing:Supports high inrush current,suitable for inductive loads and incandescent lamp loads.
2.Protection and isolation
Fuse protection:Each set is equipped with 3 A fuse to prevent overload or short circuit.
RC buffer:Each output point has a built-in RC buffer to suppress power line transient noise interference.
Optoelectronic isolation:Input/output signal isolation design to improve anti-interference ability.
3.Status indication
LED indicator:16 green LED indicators(A1 to A8)are equipped on the top to display the on/off status of each output point.
Fault alarm:The red“F”LED indicator lights up to indicate the fuse is blown.
4.Power and power consumption
Operating power supply:Only AC power supply(120 V AC)is supported.
Power consumption:All outputs are power consumption of 315 mA(from the backplane 5 V bus).
5.Environmental adaptability
Installation method:Supports DIN rail installation and is compatible with 90-30 series PLC bottom plate(5 or 10 slots).
Response time:On response time≤1 ms,off response time≤1 ms.
Operating temperature:-20°C to 60°C(some models are extended to-25°C to 70°C).
3.Typical application scenarios
Industrial Control
Motor start and stop,solenoid valve control,lighting system management.
Energy and Electricity
Substation equipment control and generator set protection.
Chemical and Manufacturing
Process control and production line equipment linkage.
Infrastructure
Water treatment system and building automation equipment.
